Mother's Day

It's hard to believe another week has gone by. Didn't get up to work on anything much this week between work and Mother's Day, but did take a couple of hours out Saturday morning to haul the trailer over to the scrap yard. We had been watching the past few months for the steel to build a new rotisserie. The last one was lent to a friend who bought the Notchback, who abandoned it at the paint shop and never returned it. Argh.

So, the second scrap yard we stooped at had just gotten a whole bunch (15 or so?) of these really nice 3x3 posts about 8-9' long. We also found some nice 2.5x2.5 posts, and some 20' 2x2s. We bought pretty much everything they had since it doesn't come in too often, and there are always tools and stands to make. It ended up being 1600lbs of steel! Each of the sizes nests pretty well into the next.

A couple of weeks back I had bought some 10" pnuematic double bearing casters when Harbor Freight had them on sale for just $10. (Tractor Supply wanted $48 for the exact same brand/model caster!) I also managed to pick up the 18.5" pnuematic rods when they were on sale.

Since the Oval is just the first of the cars that will be going in to paint soon, we're going to build adapters for the two Things, Ghias and Bugs that are all waiting to be next. It will be quite the deluxe rotisserie, but that should be great to help us in the long run when we can roll everything out in the lawn for blasting, and use the compressor to help us raise and lower the shells as we rotate them in the garage.

My friend also got a lot of work done on the template to make the H aprons, and put the order in for the Planishing Hammer this week. We finally decided that even the super cheap $130 of the Harbor Frieght Planishing Hammer wasn't worth it for a glorified air chisel. It had a max of about 220 pounds per minute, and the one we ordered had a rating up to 4000 ppm instead. The higher the better as you seek to minimize the anvil marks and smoothly pound out the metal. If all goes well, we might be able to bring a couple of reproduction aprons to Bad Camberg to see if there is any interest in them...

Great strides

We're at a point now where it seems like we're nearing the end of the disassembly, and we're starting to put things back on to the bug now. THAT is a good feeling!

It's been really hard to find the time to get up and work on the car, but Renae and the boys went to PA this weekend. It was "payback" for G and I going camping two weeks ago I suppose. So I have been taking full advantage of the situation and using my time wisely, if you will! Unfortunately, I also spent most of this weekend so far pretty sick - so out of three days, the first two went pretty slowly, but today as long as the cold meds were working so were we!

We've been making up hard to find panels from scratch. Sometimes that is pretty easy, like the inside rear apron that nobody is really going to see. But other times that is pretty difficult, like making up the outside "H" apron that EVERYONE is going to look at. We spent a little time today shaping the bar stock that will form the "H" and the little bars to either side.

Once the relief is made up, a template is used to cut out a steel blank. That steel will then be clamped to the form, and then hammered into shape. Hopefully soon we will have a planishing hammer (its on order) which will make this much easier, faster and more professional looking. The bead roller helps make the long, even grooves and shapes. It's really cool!

We got the transmission out pretty painlessly today. That was a real relief after it taking more than a dozen hours of hard labor getting the motor out last fall. We were able to save the emergency brake cables and tubes, complete with zirks. We're going to change over the brakes to a larger dual cylinder system, so most of what we took out won't necessarily be reused.

I spent a good deal of time cleaning up hardware though ~ ironically, while we can make panels large and small, matching hardware seems to be quite a problem!

There was a bit of rust that had formed in the center of the rear seat area. We knew a while ago that it had to go, so we made the repair panel some time ago - but we didn't get to actually cut out the bad area and weld in the good until now. I have to say it was a pretty challenging piece, as we had to line up panels and grooves coming from several directions.

After lots of cutting, welding, hammering, cutting, welding, hammering, cutting, welding and hammering... We got something that looks pretty darn good!

We got all of the butt welding and most of the rough shaping in tonight, but we sort of lost our light - and our steam.

So - we'll see what tomorrow brings!

Finally an update!

It's been a couple of months now since anything got posted here. Progress has been very slow since I don't get up to work on the car as often as I should. But just in the last few days we've made considerable progress.

We started inside the car, first making sure the pan was solid. Overall, it was in good shape, but a previous owner had installed carpet using nails and screws, so we had many holes to braze. And, as could be expected, the area under the battery was too weak to save. This required cutting it out, and shaping a new piece as carefully as we could to match the old. We didn't have rollers that matched the profile of the bead we needed, so we first had to make them. Then we could roll the indentations, and then cut and place the steel.

As you can see in the pictures, the patch came out really nice, although we didn't get the turning radius on the corners quite as sharp as what the stock panel was. Once painted and covered with carpet it should be far superior to having replaced it with an aftermarket panel.

Just from sitting since the 1960s she suffered some rust damage. Of course the bad repairs didn't help too much either. The area behind the back seat was "weak" so we decided to replace a good chunk of it. Again, we made up a custom panel with the exact same profile as the stock grooves, and used the English Wheel to get the proper curves. In the photo, you can see it before welding.

There was an area in the front where it appeared that the bug had been hit and the panel had separated a bit. The "professional" repair that had been done in the 1960s just lightly tacked the panels back in place without fully removing the old panels, and without fully welding them in place like the factory would have. This metal on metal and bad welding caused the steel to rot out when sand and moisture got in there, and of course left us with a bit of a surprise as to how bad some of the metalwork had really become.

On the left you can see a very common sight where the spare tire well has rotted away from past bad repairs. The apron itself was salvagable, and with a combination of panels from BFY, the original and some creative metalwork, it should look "like new" when we're done.

The drivers side clip was another big surprise. We could see that it wasn't welded in properly, but we didn't really understand how badly until we got in to it, and had to cut out the welds. Once the panels were off, I was able to grind out all of the welds and clean up the metal while my expert set to work making patches and straightening panels.

There are a couple of great things about having taken the panel off though. Now we're able to spray a rust converter into areas that would have otherwise been inaccessable to us, and of course we're able to clean and reinforce every weld union. While we have the side of the bulkhead open, this gives us the perfect opportunity to put in reinforcements and change out the mounts to put in a dual cylinder master - an "upgrade" that I believe is absolutely necessary since this restoration will not be a trailer queen.

We also found that the heat run was in not such great shape in this front kick area as we had hoped. While it was solid inside the car, the bad repair had allowed sand to get in up front there, and a small animal nest compounded the problem. In the pictures on the left here you can see the amount we had to cut away, and the panel my friend expertly stretched and shrank to fit into place.

He asked me yesterday as we worked on this if I fully appreciated the level to which we were restoring. I couldn't begin to thank him for his expertise in what we are doing. The number of hours in the smallest details is incredible. I know this won't be a Concours level restoration - in part because we're not starting with a near perfect car, but also because we have to make many of the parts we can't afford to purchase. But I know that from the inside out, every little detail will have been attended to and no body shop could afford to do the kind of restoration that we are doing.

Once all of the repairs are made to the structure of the car and she is straight and solid, we'll begin the process of removing the shell from the pan. Since this is the first of several cars we're going to be doing, we've decided to build a rotisserie. Since Harbor Freight had them on sale this week, I purchased 6 ten inch pnuematic tire swivel casters and two fully pnuematic 18in jacks. This will allow us to freely rotate the shell as we beadblast the areas that need it and we get ready to squirt her in the original L227 Stratos Silver that she will wear when complete.